• 品       牌：TI(德州仪器)
• 型       号： TPS70445PWP
  点击复制
• 商品编号： IC0135829
  点击复制
• 封装规格：
  点击复制
• 商品描述： The TPS704xx family of devices consists of dual-output, low-dropout voltage regulators with integrated SVS (; , POR, or power on reset) and power good (PG) functions. These devices are capable of supplying 1 A and 2 A by regulator 1 and regulator 2 respectively. Quiescent current is typically 185 µA at full load. Differentiated features, such as accuracy, fast transient response, SVS supervisory circuit (power on reset), manual reset input, and independent enable functions provide a complete system solution.; The TPS704xx family of voltage regulators offers very low dropout voltage and dual outputs. These devices have extremely low noise output performance without using any added filter bypass capacitors and are designed to have a fast transient response and be stable with 47-µF low ESR capacitors.; These devices have fixed 3.3-V/2.5-V, 3.3-V/1.8-V, 3.3-V/1.5-V, 3.3-V/1.2-V, and adjustable voltage options. Regulator 1 can support up to 1 A, and regulator 2 can support up to 2 A. Separate voltage inputs allow the designer to configure the source power.; Because the PMOS device behaves as a low-value resistor, the dropout voltage is very low (typically 160 mV on regulator 1) and is directly proportional to the output current. Additionally, since the PMOS pass element is a voltage-driven device, the quiescent current is very low and independent of output loading (maximum of 250 µA over the full range of output current and full range of temperature). This LDO family also features a sleep mode; applying a high signal to; or; (enable) shuts down regulator 1 or regulator 2, respectively. When a high signal is applied to both; and; , both regulators enter sleep mode, thereby reducing the input current to 2 µA at T; = +25°C.; For each regulator, there is an internal discharge transistor to discharge the output capacitor when the regulator is turned off (disabled).; The PG1 pin reports the voltage condition at V; . The PG1 pin can be used to implement a SVS (; , POR, or power on reset) for the circuitry supplied by regulator 1. The PG2 pin reports the voltage conditions at V; . The PG2 pin can be used to implement a SVS (power on reset) for the circuitry supplied by regulator 2.; The TPS704xx features a; (SVS, POR, or power on reset).; is an active low, open drain output and requires a pull-up resistor for normal operation. When pulled up,; goes into a high impedance state (that is, logic high) after a 120-ms delay when both of the following conditions are met. First, V; must be above the undervoltage condition. Second, the manual reset (; ) pin must be in a high impedance state. To monitor V; , the PG1 output pin can be connected to; . To monitor V; , the PG2 output pin can be connected to; .; can be used to drive power on reset or a low-battery indicator. If; is not used, it can be left floating.; Internal bias voltages are powered by V; and require 2.7 V for full functionality. Each regulator input has an undervoltage lockout circuit that prevents each output from turning on until the respective input reaches 2.5 V. The TPS704xx family of devices consists of dual-output, low-dropout voltage regulators with integrated SVS (; , POR, or power on reset) and power good (PG) functions. These devices are capable of supplying 1 A and 2 A by regulator 1 and regulator 2 respectively. Quiescent current is typically 185 µA at full load. Differentiated features, such as accuracy, fast transient response, SVS supervisory circuit (power on reset), manual reset input, and independent enable functions provide a complete system solution.; The TPS704xx family of voltage regulators offers very low dropout voltage and dual outputs. These devices have extremely low noise output performance without using any added filter bypass capacitors and are designed to have a fast transient response and be stable with 47-µF low ESR capacitors.; These devices have fixed 3.3-V/2.5-V, 3.3-V/1.8-V, 3.3-V/1.5-V, 3.3-V/1.2-V, and adjustable voltage options. Regulator 1 can support up to 1 A, and regulator 2 can support up to 2 A. Separate voltage inputs allow the designer to configure the source power.; Because the PMOS device behaves as a low-value resistor, the dropout voltage is very low (typically 160 mV on regulator 1) and is directly proportional to the output current. Additionally, since the PMOS pass element is a voltage-driven device, the quiescent current is very low and independent of output loading (maximum of 250 µA over the full range of output current and full range of temperature). This LDO family also features a sleep mode; applying a high signal to; or; (enable) shuts down regulator 1 or regulator 2, respectively. When a high signal is applied to both; and; , both regulators enter sleep mode, thereby reducing the input current to 2 µA at T; = +25°C.; For each regulator, there is an internal discharge transistor to discharge the output capacitor when the regulator is turned off (disabled).; The PG1 pin reports the voltage condition at V; . The PG1 pin can be used to implement a SVS (; , POR, or power on reset) for the circuitry supplied by regulator 1. The PG2 pin reports the voltage conditions at V; . The PG2 pin can be used to implement a SVS (power on reset) for the circuitry supplied by regulator 2.; The TPS704xx features a; (SVS, POR, or power on reset).; is an active low, open drain output and requires a pull-up resistor for normal operation. When pulled up,; goes into a high impedance state (that is, logic high) after a 120-ms delay when both of the following conditions are met. First, V; must be above the undervoltage condition. Second, the manual reset (; ) pin must be in a high impedance state. To monitor V; , the PG1 output pin can be connected to; . To monitor V; , the PG2 output pin can be connected to; .; can be used to drive power on reset or a low-battery indicator. If; is not used, it can be left floating.; Internal bias voltages are powered by V; and require 2.7 V for full functionality. Each regulator input has an undervoltage lockout circuit that prevents each output from turning on until the respective input reaches 2.5 V.